CNC Rotation 4th Axis 130mm 3-jaw 4 Jaw Chuck Dividing Head 4:1+Tailstock+Nema34
1). If you choosed "With Nema34 Stepper Motor No Driver"
Package include:
- 1 x CNC 4th rotary axis with chuck with Nema34 Stepper Motor (3 jaw chuck or 4 jaw chuck are optional)
- 1 x 100mm MT2 tailstock
2). If you choosed "With Nema34 Stepper Motor Driver Kit"
Package include:
- 1 x CNC 4th rotary axis with chuck with Nema34 4.5N.m Stepper Motor (3 jaw chuck or 4 jaw chuck are optional)
- 1 x 100mm MT2 tailstock
- 1 x DMA860S Stepper Motor Driver
- 1 x 400W 60V DC Switching power supply (Optional)
3). If you choosed "With Nema34 Closed Loop Motor Driver Kit"
Package include:
- 1 x CNC 4th rotary axis with chuck with Nema34 4.5Nm Closed Loop Servo Motor (3 jaw chuck or 4 jaw chuck are optional)
- 1 x100mm MT2 tailstock
- 1 x 2HSS86 Servo Motor Driver
- 1 x 400W 60V DC Switching power supply (Optional)
Descriptions:
|
CNC 4th-Axis A-Axis Rotation-Axis Kit K11-130mm
- Product Model: 5M-H100-4-130A
- Chuck type: K11-130mm 3-jaw centring chuck
- Centre height: 100MM
- Total height: 165MM
- Through-hole diameter: 30MM
- Angle: 0.45 degree/step
- Deceleration ratio: 4:1 (synchronous belt deceleration mode)
- Stepping motor: 2-phase 4-wire 86 stepping motor (current 4.5A)
- Accessories: one pair of total counter claw and spanner (as shown)
- Synchronous belt: 5M-450 (width 15MM)
CNC 4th-Axis A-Axis Rotation-Axis Kit K12-130mm
- Product Model: 5M-H100-4-130B
- Chuck type: K11-130mm 4-jaw centring chuck
- Centre height: 100MM
- Total height: 165MM
- Through-hole diameter: 30MM
- Angle: 0.45 degree/step
- Deceleration ratio: 4:1 (synchronous belt deceleration mode)
- Stepping motor: 2-phase 4-wire nema34 motor (open loop stepper motor or closed loop stepper motor are optional)
- Accessories: one pair of total counter claw and spanner (as shown)
- Synchronous belt: 5M-450 (width 15MM)
Four-axis pulse equivalent setting:
Mach3 system setting:
- Number of pulses required for 1 degree
- (Number of pulses for 1 revolution of the motor x number of fine points of the driver x reduction ratio) ÷ 360 degrees
- For example, two-phase 86 motor, fine fraction 16, reduction ratio 4:1
- (200×16×4)÷360=35.555555555555555)
VI-VO-TEK system setting:
- Angle travelled by 1 pulse
- 360 degrees ÷ (motor 1 circle pulse × drive fine points × reduction ratio)
- For example: two-phase 86 motor, the number of fine points 16, reduction ratio: 1
- 360÷(200×16×4)=0.028125
If the X or Y axis is used instead the algorithm is:
- Circumference ÷ (motor 1 turn pulse number × driver fine fraction × reduction ratio)
- The equivalents are set for engraving round bars of different sizes
86HSE82 Nema34 Closed loop Servo motor 4.5N.m
- Size:86x86x82mm
- Current :6.0A; Phase:2
- Step Angle(degrees):1.8 degree
- Lead wire:4pcs
- Holding Torque:450Ncm
- Resistance:0.44±10%Ω
- Inductance:3.7±20%mH
- Insulation resistance:100MOhm(500V DC)
- Insulation Class:B
- Type: Closed-loop stepper motor
If you choose "Nema 34 stepper motor",the parameters of the motor is as follows:
- Stepping angle: 1.8°±5
- Number of phases: 2
- Current: 4.5A
- Holding torque 4.5N.m
- Inductance: 2.8°±10%Ω
- Insulation class: B
- Resistance: 0.32 0.32°±10%Ω
- Insulation resistance: 400MOhm ( 500VDC)
- Type: Open-loop stepper motor
2HSS86 Servo Motor Driver:
Parameter
- Voltage range: AC24~70V or DC30~100V
- Peak current: 8.0A
- Frequency: 0~200KHz
- Encoder lines: 1000
- Insulation resistance: ≥500MΩ
- Storage temperature： 0~50℃
- Cooling method: Natural or radiator
- Operating Occasions: try to avoid dust, oil, corrosion gas
- Operating temprature: 0~50℃
- Operating humidit: 40~90%RH
- virbration: 5.9m/s2Max
Signal controller port
- If the signal control voltage is +5V, then the signal control input port do not need to connect an extra resistance. If the signal control voltage is +12V, then the signal control input port need to connect to a 1K resistance. If the signal control voltage is +12V, then the signal control input port need to connect to a 2K resistance.
- OC output, closed indicate finish the position, open circuit indicate position is not finished.
- OC output, there is alarm signal when closed, no alarm signal when open circuit.
DMA860S Nema34 Stepper Motor Driver:
ELECTRICAL SPECIFICATIONS
- Output Current: 2.2-8.2A
- Supply Voltage: 18-110VAC ( Typical value: 80VAC ); 18-160VDC ( Typical value: 90VAC )
- Control Single Current: 5-20mA ( 10mA )
- Pulse Frequency: 0-300KHz
- Pulse Width: 2 us
- Direction Single Width: 100 us
- Undervoltage Protection: 7.5 VDC
- Overvoltage Protection: 170 VDC
- Drive Initialization Time: 2 S
- Insultation Resistance: 500 MΩ
SUMMARY
- DMA860S 2 phase stepper motor driver is a cost-effective subdivision driver designed based on Pl control algorithm. It has excellent performance,high speed and high torque output,low noise,low vibration,and low heat.
- The DMA860S driver can select the current and subdivision through the DIP switch. There are 16 subdivisions and 16 currentfor selection. It has overvoltage, undervoltage, phase current and total current overcurrent protection. The input and outputcontrol signal all use photoelectric isolation.
CHARACTERISTIC
- Pl control algorithm, low noise, low vibration, low heat generation;
- Signal input:single-ended,pulse + direction and double pulse;
- Built-in micro-subdivision; power supply range:AC18V-110V.DC18V-160V;
- The current setting is convenient, 16 gears are optional, and the peak value of theoutput current can reach 8.2A;the current is halved after the IS is stationary;
- The factory default maximum subdivision is 128,16 steps are adjustable;
- Optically isolated differential signal input, the maximum input pulse frequency is300KHz;
- With overvoltage, undervoltage alarm, phase current overcurrent protection,motorphase open circuit detection and other functions;
- The pulse, direction and enable terminalshave constant current input function,whichcan be directly connected to the input signal,Instead of adding a series resistor forstep-down current-limiting protection;
- High reliability: using multi-layer boards and surface mount packaging,leavingenough margin for power devices.
MT2 Tail Top
- Centre height: 100mm
- Telescopic stroke: 50mm
- Base length: 120mm
- Base material: aluminium alloy
- Tip: Use Morse 2 tip.
- Accessories: with axial locking spanner
K11-130mm three-jaw centring chucks
- Maximum input torque: 100N.m
- Limit speed: 3000r/min
- Maximum static clamping force: 17KN
- Clamping range
- Positive jaw clamp: 3-40mm
- Positive jaw support: 40-130mm
- Reverse Jaw Clamp: 40-120mm
- Mounting screw: M8
K12-130mm four-jaw centring chucks
- Maximum input torque: 100N.m
- Limit speed: 3000r/min
- Maximum static clamping force: 17KN
- Clamping range
- Positive jaw clamp: 3-40mm
- Positive jaw support: 40-130mm
- Reverse Jaw Clamp: 40-120mm
- Mounting screw: M8
- Smooth high-speed operation, high repetitive positioning accuracy, large clamping force, suitable for automated production
- Precision processing, high tensile strength, quenching and hardening, high quality raw materials, rust and corrosion resistance
- Jaws of 45 steel quenched as a whole, soft inside and hard outside to use more durable
- Jaws jaws with non-slip design, stable clamping without slipping
- Centre through-hole, use and processing of a wide range of parts such as bars, can replace the jaws, the use of connecting flanges, easy to use
400W 60VDC Switching Power Supply
- Output voltage: 60V DC;
- Output Frequency:85%;
- Output Current:6.6A;
- Inlet/Load stability:±0.5%;
- DC voltage of Adjustable range:±10%;
- AC input voltage range: 110V/220V ±15% (Switch Selection) (95-120V or 220V-240V); Overload protection:105%-135% hiccup mode,auto-recovery;
- Over-voltage protection:115%-150% rated output voltage; Working temperature-10℃～+50℃.
Avvantages
- Constant-rotating ball fan, fast heat dissipation, fast speed, protect the internal components pf the switching power supply.
- The shell is made of aluminum alloy with high thermal conductivity system ,which is reinforced and durable, and the design is more use-friendly.
Wiring port description
- +V ADJ: output voltage regulation
- +V: DC power output “+”
- -V: DC power output “-“
- N: Negative wire
- L: Live wire
Shipping Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately Items will be shipped within 1-2 days upon the receipt of payment.
Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. We are a new member in ebay now, and need understand both of sides Pls email us before you want to leave any negative feedback
Refund When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Contact us Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s message within 1-2 business days,if not pls check the mail box again Customer’s satisfaction is very important to us.
Shipping
Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately
Items will be shipped within 1-2 days upon the receipt of payment.
Problem&Feedback
Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it.
We are a new member in ebay now, and need understand both of sides
Pls email us before you want to leave any negative feedback
Refund
When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos
Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Contact us
Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s message within 1-2 business days,if not pls check the mail box again
Customer’s satisfaction is very important to us.
