Details
Descriptions:
1. Water flow sequence: enter water from the high pressure end, flow to the low pressure end, and ensure that the tungsten rod at the high pressure end is upward (tungsten rod structure laser tube), the water inlet is at the bottom, the tungsten rod at the low pressure end is placed downward, and the water outlet is at the top (applicable to All structured laser tubes). Drain all the air bubbles and fill it with water (no water, no water, and air bubbles will cause the inner tube to burst, and the warranty will not be covered). Finally, fasten the rubber tube with cable ties, so that no water seeps out, so as to prevent the ignition failure outside the tube caused by water leakage.
2. Required flow rate: 4-5 liters/minute of water flow. If you use a water pump, please ensure that the water quality is pure, and replace the pure water once a week.
3. Water temperature requirements: within 30 degrees, the higher the water temperature, the greater the power fluctuation of the laser tube, and the speed will obviously weaken.
4. Wiring treatment: After pulling out the high-voltage wires and low-voltage wires, wrap the copper wires tightly under the screw gaskets at both ends, tighten the screws to clamp the copper wires, (use electrical plastic bags to wrap the wires thickly, and wrap them as wide as possible. thicker, which can more effectively prevent ignition leakage, etc.), and then cover the high-voltage dust cover specially equipped for the high-voltage end to compress the entire high-voltage end, and use plastic wrap to wrap the high-voltage end or the entire pipe body to prevent dust Potential malfunction due to contamination of ambient humidity.
 
Package List:
1x CO2 Laser Tube
Power: 50W -55W Length: 800mm Diameter: 50mm;
Versatile and an excellent replacement for laser tubes of the same power or length. Please check the diameter and length of the laser tube before ordering to ensure that the laser tube can be installed on the machine as a replacement.
Pre-wiring: For the convenience of installation, the high-voltage and low-voltage ports have been connected in advance.
TEM00 mode: the output laser is TEM00 mode, with high spot concentration, high energy density, and stable spot, which makes the laser machine perform better.
Metal head: The metal head is not as easy to break as the glass head laser tube, and has a longer service life.
This CO2 laser tube is mainly used for laser cutting machine or laser engraving machine, which can engrave and cut acrylic, cloth, leather, bamboo, wood, engraving, etc.

We only ship to US mainland 48 states and worldwide via ebay international shipping program. We don't offer direct international shipping. Consult us if you live in Hawaii, Alaska or Virgin Islands. Also we don't ship to any APO/FPO/PO BOX address. We offer FedEx Ground or Home delivery in optional which can make it faster, charge additional shipping fee.

Delivery is any day from 1-4 business days (Monday through Friday, excluding weekends and holidays)

This item is covered by our 12 months unlimited mileage warranty.

Any customer may use the same outlets to facilitate a return or warranty claim. Any item must be returned within 30 days of the original purchase for refund; item(s) retaining a warranty may be returned beyond 30 days but within the remaining warranty period. Returns that are not subject to warranty may accrue a restocking fee and should be returned at the customers cost.

Dailyworth reserves the right to request proof of purchase and mechanical failure in the event of any warranty claim; any returns or claims that violate Ebay's Online Return policies will be reported. Dailyworth holds no responsibility or liability for additional repairs, damages (punitive or non-punitive), loss of time, or any other extraneous circumstances created by a purchase made from said party."

 

We understand that sometimes you need to make a return or an exchange. All we ask is you send it back in the same condition it was received - new and un-used.

If the product you receive is not the one you ordered, please take photos of any visible of visual reference and contact us directly; photos must be CLEAR and VISIBLE. Logistical claims must be filed within 30 days of received the product; exchanges in these cases will be handled promptly and at?no cost to the customer.

In order to process a return or exchange, please call us or send us a message through eBay and we will be happy to assist you immediately.

However，any return that is NOT defective or NOT received in error, is the responsibility of the customer. We DO NOT cover any shipping costs and/or additional fees associated with the transaction.

Dailyworth has always been our mission to offer viable solution for MRO & outdoor products and automobile accessories adhering to the highest standards in quality, materials and workmanship, while enabling our clients to enjoy substantial profit and maximize value for the end user.

We are open Monday to Friday 8am to 5pm Mountain Standard Time, and Saturday 9am to 1pm MST. Our friendly staff are available during these hours. Please feel free to call us, or send us a message via eBay.

We aim for complete customer satisfaction and repeat business; we will be more than happy to help you feel 100% comfortable with your purchase.

DataCaciques