BrewZilla Gen 4 100L All Grain Brewing System

The BrewZilla Gen 4 100L is a single vessel all grain brewing system for batches up to 90L, with three 2200W heating elements, a built-in pump and a wifi-connected controller. It runs on a 32A single phase supply, or a qualified electrician can convert it to a 10A three phase connection. The elements are deliberately low watt density, which keeps the wort off a scorching hot surface. That means less caramelisation in pale beers, fewer boilovers and an easier clean-up. The base drains fully into a concave floor, so you are not tilting the vessel to get the last of the wort out, and a false bottom screen catches around 95% of hops and hot break before they reach the pump. Pump and malt pipe The 25W magnetic drive pump handles liquid up to 120°C and draws 1.1A, so it can run continuously through a mash. The base holds a sealed electronics junction box instead of a bottom cover, which makes the pump easy to reach and the plumbing easy to re-route or bypass. The two stage malt pipe holds 72L, carries 30% more grain than the previous design and lifts in two stages rather than one heave. Its perforated lower section improves sparge and lauter flow. RAPT controller The controller has a full colour screen on a tilting frame at standing height, and it unclips for wash-down. Delay timing and step mash programming are built in. It connects to the RAPT portal over wifi, where you can log a brew, watch it from another room and control the system remotely, with push notifications when it is time to add hops or start the boil. You can set your own alarms and step messages for grain additions, mash-out, sparge and salt timings. It also works as a Bluetooth gateway, reading BLE thermometer sensors so the system can act on a temperature taken in the malt pipe or the coolant water rather than at the element. Specifications Boiler volume: 107L brimful Maximum batch size: 90L Malt pipe volume: 72L Elements: 3 x 2200W, 6.6kW maximum Pump: 25W magnetic drive, 3.4m maximum head, 19 litres per minute maximum flow Supply: 220-240V AC, 32A single phase, non-removable lead Outside diameter: 52cm approximately, or 59cm including the handles Height: 70cm approximately for the boiler, 94cm including the recirculation arm Dry weight: 20kg Warranty: 12 months If you are unsure whether a 32A supply is workable where you brew, get in touch before you order.

BrewZilla Gen 4 100L All Grain Brewing System

The BrewZilla Gen 4 100L is a single vessel all grain brewing system for batches up to 90L, with three 2200W heating elements, a built-in pump and a wifi-connected controller. It runs on a 32A single phase supply, or a qualified electrician can convert it to a 10A three phase connection.

The elements are deliberately low watt density, which keeps the wort off a scorching hot surface. That means less caramelisation in pale beers, fewer boilovers and an easier clean-up. The base drains fully into a concave floor, so you are not tilting the vessel to get the last of the wort out, and a false bottom screen catches around 95% of hops and hot break before they reach the pump.

Pump and malt pipe

The 25W magnetic drive pump handles liquid up to 120°C and draws 1.1A, so it can run continuously through a mash. The base holds a sealed electronics junction box instead of a bottom cover, which makes the pump easy to reach and the plumbing easy to re-route or bypass. The two stage malt pipe holds 72L, carries 30% more grain than the previous design and lifts in two stages rather than one heave. Its perforated lower section improves sparge and lauter flow.

RAPT controller

The controller has a full colour screen on a tilting frame at standing height, and it unclips for wash-down. Delay timing and step mash programming are built in. It connects to the RAPT portal over wifi, where you can log a brew, watch it from another room and control the system remotely, with push notifications when it is time to add hops or start the boil. You can set your own alarms and step messages for grain additions, mash-out, sparge and salt timings. It also works as a Bluetooth gateway, reading BLE thermometer sensors so the system can act on a temperature taken in the malt pipe or the coolant water rather than at the element.

Specifications

  • Boiler volume: 107L brimful
  • Maximum batch size: 90L
  • Malt pipe volume: 72L
  • Elements: 3 x 2200W, 6.6kW maximum
  • Pump: 25W magnetic drive, 3.4m maximum head, 19 litres per minute maximum flow
  • Supply: 220-240V AC, 32A single phase, non-removable lead
  • Outside diameter: 52cm approximately, or 59cm including the handles
  • Height: 70cm approximately for the boiler, 94cm including the recirculation arm
  • Dry weight: 20kg
  • Warranty: 12 months

If you are unsure whether a 32A supply is workable where you brew, get in touch before you order.

×
×
×

Buy now and save!

Shipping info

Click the Shipping & Payments tab above the listing description for more info

Click the Shipping & Payments tab above the listing description for more info!

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYMENT


Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via All Major Credit Cards (Visa, Mastercard, AMEX, Discover), Google Pay, PayPal, & Apple Pay (on mobile & eBay App).

Thank you for shopping with us on eBay!

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© Distillery King

Click the Shipping & Payments tab above the listing description for more info

Accepted Payment Methods

Immediate payment is required upon selecting "Buy It Now" or upon checking out through the cart.

We accept payment via All Major Credit Cards (Visa, Mastercard, AMEX, Discover), Google Pay, PayPal, & Apple Pay (on mobile & eBay App).

Thank you for shopping with us on eBay!

Returns are accepted

Items must be returned within 30 days of the auction ending

Buyer will pay for return shipping.