ERYONE PETG or PLA Carbon Fiber Filament: Ideal for Strong Lightweight Prints

ERYONE Carbon Fiber filament is provide strong yet lightweight prints. Thanks to the infusion of Carbon Fiber into the filament you can create prints with thinner side walls without sacrificing rigidity. Available in both PLA and PETG you can choose the most suitable base material for your required design. Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent. Features: Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable PrintsMinimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise. Purest-grade Material | Made in USA Professional Packaging | Vacuumed SealedERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models. High Compatibility: Compatible with most 3D Printers that support 1.75mm PLA or PETG filament. NOTE: Requires good ventilation during printing due to the presence of styrene. Specifications: Filament Diameter: 1.75mm Tolerance: ± 0.03mm Print Temperature PLA Carbon Fiber: 190-220°C Print Temperature PETG Carbon Fiber: 220-240°C Heated Bed Temp: 55-70°C Fan Speed: None to Minimal Recommended Print Speed 30-60mm/s Produced mainly from Corn Starch, eco friendly material. Net Weight: 1kg (inc spool) Gross Weight: 1.3-1.4kg FAQ: Clogging: Clogging is caused by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging. Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be caused. Reducing the temperature and speed corrections will solve these issues. Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.


ERYONE PETG or PLA Carbon Fiber Filament: Ideal for Strong Lightweight Prints

ERYONE Carbon Fiber filament is provide strong yet lightweight prints. Thanks to the infusion of Carbon Fiber into the filament you can create prints with thinner side walls without sacrificing rigidity. Available in both PLA and PETG you can choose the most suitable base material for your required design.

Quality is at the heart of ERYONE, Founded in 2018, Headquartered in Shenzhen, the heart of Chinese Electronics, ERYONE benefits from direct access to raw material suppliers and young talent.

Features:

  • Minimum Tolerance | Low Warping | Ensure Consistent Feeding and Stable Prints
    Minimum tolerance and low warping to ensure consistent feeding and stable prints, No clogging, extremely high successful rate, resulting in printed parts that have an outstanding surface finish and are highly precise.
  • Purest-grade Material | Made in USA
  • Professional Packaging | Vacuumed Sealed
    ERYONE is supplied in a sealed vacuum bag with a desiccant bag to keep it dry and keep out dust and foreign particles, prevent nozzle jams and yield smooth 3D models.
  • High Compatibility: Compatible with most 3D Printers that support 1.75mm PLA or PETG filament.
  • NOTE: Requires good ventilation during printing due to the presence of styrene.

Specifications:

  • Filament Diameter: 1.75mm
  • Tolerance: ± 0.03mm
  • Print Temperature PLA Carbon Fiber: 190-220°C
  • Print Temperature PETG Carbon Fiber: 220-240°C
  • Heated Bed Temp: 55-70°C
  • Fan Speed: None to Minimal
  • Recommended Print Speed 30-60mm/s
  • Produced mainly from Corn Starch, eco friendly material.
  • Net Weight: 1kg (inc spool)
  • Gross Weight: 1.3-1.4kg

FAQ:

  • Clogging: Clogging is causéd by uneven wire diameter or too low a temperature. Clean the nozzle before use and raise the temperature to reduce the chance of clogging.
  • Stringing: If the temperature is too high, the flow of PLA is too fast, or the feed parameters are not set properly, wire stringing will be causéd. Reducing the temperature and speed corrections will solve these issues.
  • Over Extrusion: Too high a temperature, too slow speed, or nozzle diameter in the section does not match will cause too much extruding at the nozzle outlet, and there will be residual material.


×
×
×
×
×
×
×
×
×
×
×
×

Tell a friend Visit store Watch now

Should you have any questions regarding this item, please contact our Customer Service Team. Click the button below and our Customer Service team will be happy to assist.

Ask seller a question

© NSE Imports

  • All items are shipped with full tracking to ensure safe arrival.
  • If we do not ship to your country please contact us for pricing, we will be happy to help.
  • Click the Postage tab above the listing description for more info

Accepted Payment Methods

  • PayPal
  • PayPal Credit
  • Google Pay
  • Apple Pay
  • Most major Credit and Debit cards

Returns are accepted, we hope your item arrives in good order and meets your expectations.
Should this not be the case, please contact us before opening a return.

Items must be returned within 30 days of the auction ending

Seller will pay for return shipping.